Nissan Primera Owners Club Nissan Primera Owners Club > General Open Forums - NO TRADING! > Nissan Primera Help & Queries
  New Posts New Posts RSS Feed - Nissan primera P12 F9Q oil pan removal
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Nissan primera P12 F9Q oil pan removal

 Post Reply Post Reply
Author
Message
petterg View Drop Down
NPOC Guest
NPOC Guest


Joined: 01 Jun 2014
Location: Norway
Online Status: Offline
Points: 325
Post Options Post Options   Thanks (0) Thanks(0)   Quote petterg Quote  Post ReplyReply Direct Link To This Post Topic: Nissan primera P12 F9Q oil pan removal
    Posted: 02 Dec 2017 at 4:40pm
Nissan Primera P12 2004 (post facelift) 1.9dci (F9Q) 6 speed manual

I have a oil leak between the oil pan and engine. Does anyone know if I need to remove the gearbox/clutch housing from engine in order to get the oil pan off?
Back to Top
p11primeragt View Drop Down
NPOC Elite Member
NPOC Elite Member
Avatar

Joined: 29 Jul 2011
Location: North east
Online Status: Offline
Points: 18268
Post Options Post Options   Thanks (0) Thanks(0)   Quote p11primeragt Quote  Post ReplyReply Direct Link To This Post Posted: 02 Dec 2017 at 5:08pm
Are you sure it's from the sump itself or it could be the rear main crank seal?
Back to Top
timeshock! View Drop Down
NPOC Member
NPOC Member
Avatar

Joined: 29 Jan 2006
Location: Newcastle
Online Status: Offline
Points: 13113
Post Options Post Options   Thanks (0) Thanks(0)   Quote timeshock! Quote  Post ReplyReply Direct Link To This Post Posted: 02 Dec 2017 at 6:00pm

If it is the pan this is taken from the ESM for your engine

 
CAUTION:

To avoid the danger of being scalded, never drain the engine oil when the engine is hot.

REMOVAL

1. Remove engine undercover.

2. Remove RH front wheel.

3. Remove right side splash cover.

4. Remove front drive shaft assembly RH side. Refer to FAX-11, "FRONT DRIVE SHAFT" .

5. Remove rear torque rod mounting bolt as shown.

6. Drain engine oil. Refer to LU-16, "Changing Engine Oil" .

CAUTION:

Perform when engine is cold.

MBIB0951E

1. Baffle plate 2. Gasket 3. Oil pan

4. O-ring 5. Drain plug 6. Oil level gauge (with oil filer cap)

7. Crankshaft position sensor

MBIB0952E

OIL PAN

EM-151

[F9Q]

C

D

E

F

G

H

I

J

K

L

M

A

EM

7. Remove oil pan and transaxle joint bolts.

8. Support the engine bottom of the oil pan with a transmission jack

etc.

9. Remove oil pan bolts in the reverse order as shown.

l Insert seal cutter (special service tool) between oil pan and

cylinder block. Slide tool by tapping on the side of the tool with

a hammer.

CAUTION:

Exercise care not to damage mating surface.

10. Remove oil pan.

MBIB0953E

MBIB0954E

MBIB0820E

SEM365EA

EM-152

[F9Q]

OIL PAN

11. Remove baffle plate mounting bolt, then remove baffle plate.

INSPECTION AFTER REMOVAL

Clean oil pump assembly if any object attached.

INSTALLATION

l Install in the reverse order of removal paying attention to the following.

1. Install baffle plate.

2. Apply liquid gasket as shown.

l Use Genuine Liquid Gasket or equivalent.

3. Install oil pan bolts in the numerical order as shown.

4. At least 30 minutes after oil pan is installed, pour engine oil.

INSPECTION AFTER INSTALLATION

l Inspection the engine oil level. Refer to LU-16, "ENGINE OIL" .

l Start the engine, and make sure there is no leak of engine oil. Refer to LU-16, "ENGINE OIL" .

Back to Top
 Post Reply Post Reply

Forum Jump Forum Permissions View Drop Down

This forum is optimised for a 1024x768 screen resolution

Copyright © 2001-2017 Nissan Primera Owners Club. All rights reserved.